Built different.
Built here.
Battery, tool and charger wall mounts for 10 platforms. Screw in, peel and stick, or magnetic. Any color on any holder. Printed in PETG and shipped from Seaside, CA.
KCS-WM / BATTERY HOLDERS
Shop wall mounts by battery platform
$5 a piece, $4 each at 4 or more. EGO 56V holders are $12, or $10 each for 2 or more. Any color on any holder.
Start a wall
Pick a starter wall and it drops into your cart. Change any piece, color or platform before you check out.
Milwaukee M18 wall mounts
Pick a platform and a color, then add exactly the pieces you need. Mix platforms and colors in one cart. $5 a piece, $4 each at 4 or more. EGO 56V holders are $12, or $10 each for 2 or more.
1 / Platform:
2 / Color:
Same price in every color. Need your company color? Ask me.
3 / Pieces and mounts:
Each tap goes straight into your cart. Switch the platform or color to add more, they all share one cart.
Tool holders mount under a shelf or bench edge so the tool hangs down. Holders only: tools, batteries, chargers and screws are not included.
How they mount
Each holder is sized to its own platform, so the battery slides in the same way it slides into the tool.
Tools hang under a shelf
Tool holders screw to the underside of a shelf, cabinet or bench edge, and the tool hangs straight down. They aren't made to go flat on a wall.
Batteries go on the wall
Battery holders screw flat to a wall, stud or pegboard. The battery clicks in and locks the same way it does on the tool. Press the release to take it off.
Chargers too
Add the mount for your charger and the whole station comes off the bench. Ridgid and Ryobi have two charger shapes, so pick the one that looks like yours.
Three ways to mount
Screws into a stud, pegboard, plywood or a bench. Works on every piece. Screws are not included, so use whatever suits what you're mounting to.
A strip of 3M VHB tape goes on the back before it ships. Clean the spot with rubbing alcohol, peel, press it on hard for 30 seconds, and give it 24 hours before you hang a battery. Works on aluminum toolboxes, truck boxes and painted walls. Every brand except Milwaukee M12, whose back is too small for the tape, and EGO for now.
Four magnets sealed inside the back, with rubber feet so they don't slide. They stick to a steel toolbox, cart or shelf with no screws. Not for aluminum.
Real photos
Every shot here is a holder I printed, on a real bench.
“I bought a set of the other material first. They melted right off the wall.”
Outfitting a crew or a fleet?
Fleet colors, company colors and bulk orders. I can print a whole order in your company color so every truck's holders match. Tell me the color, the brands and how many, and I'll quote it.
Questions
If I pick orange for my Milwaukee, what do I get?
Milwaukee holders printed in orange. The color photo on this page may show a different brand's holder in that color. The fit always matches the platform you pick.
Why PETG?
Most budget holders are printed in PLA, the cheapest and softest plastic there is. Leave one in a closed truck through a summer and it goes soft, and a loaded drill slowly works its way off the wall. PETG takes a lot more heat before anything moves.
What does see-through look like?
Translucent plastic in the color you pick. You can see light through it, and on the magnetic holders you can see the magnets sealed inside. They're limited edition, so when a roll runs out, that color comes off the site.
Do the magnetic holders work on aluminum?
No. Magnets only stick to steel. For an aluminum box, pick the VHB battery holder, or use the screw holes, which are still on every magnetic holder.
How does the price work?
Every piece is $5, or $4 each once your cart has 4 or more. That counts every piece in the cart, across brands and colors. Magnetic battery holders are $5 more each, and VHB battery holders are $1 more. The EGO 56V holder is a much bigger part, so it's priced on its own: $12 for one, $10 each for 2 or more, and it doesn't count toward the $4 tier. Shipping is $5.97 flat, and free once your cart reaches $35, which is about 9 pieces.
Which charger mount do I need?
Each brand lists its charger mounts under Pieces. Bosch, Makita and EGO don't have one yet. Not sure which charger you have? Email a photo to admin@klauscustom.com and I'll tell you.
How fast does it ship?
Usually out in 1 to 2 business days, by USPS Ground Advantage. Delivery is normally 3 to 8 business days after that. See the shipping page.
Can I mount without screws?
Yes. Pick the VHB battery holder and it ships with 3M VHB tape already on the back. Clean the spot with rubbing alcohol, peel, press hard for 30 seconds, and wait 24 hours before loading a battery. On steel, the magnetic holders work too.
Will the battery fall out in a moving truck?
No. The battery clicks in and locks the same way it does on the tool, and it stays put until you press the battery's release button. That goes for the screw-in, VHB and magnetic battery holders. The EGO 56V holder works differently: the pack slides down onto its rails and lifts straight off.
Are screws included?
No. Use whatever suits what you're mounting to. The holders are the only thing in the box.